Iron catalyst

1271-42-7, Ferrocenecarboxylic acid is a iron-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

In a 50mL three necks round bottom flask and under nitrogen atmosphere, 1mmol of ferrocenecarboxylic acid was dissolved in 15mL of dry dichloromethane at room temperature. To this solution, 170-200muL of oxalyl chloride was added dropwise and stirred overnight. The solution changed from orange to dark red. The reaction mixture was filtered in a fritted funnel and the filtrate collected. In a separate 100mL three necks round flask under nitrogen, 1.0mmol of the 4-X-phenol and 1.0mmol of pyridine were dissolved in 10-15mL of dichloromethane. To this solution, the ferrocenecarbonyl chloride solution prepared previously was added dropwise. The solution was stir 6-12hin the dark, under nitrogen atmosphere, and at room temperature. Thin layer chromatography (TLC) was used to monitor the reaction. After the reaction was finished, the mixture was filtered in a fritted funnel with a pad of celite. The filtrate collected was washed with 3¡Á5mL 1N HCl to remove pyridine and other by-products. The organic layer containing the compound was purified by column chromatography, using Silica gel and eluted with dichloromethane and isolated in 40-45% yield.

1271-42-7, 1271-42-7 Ferrocenecarboxylic acid 499634, airon-catalyst compound, is more and more widely used in various fields.

Reference£º
Article; Vera, Jose L.; Rullan, Jorge; Santos, Natasha; Jimenez, Jesus; Rivera, Joshua; Santana, Alberto; Briggs, Jon; Rheingold, Arnold L.; Matta, Jaime; Melendez, Enrique; Journal of Organometallic Chemistry; vol. 749; (2014); p. 204 – 214;,
Iron Catalysis in Organic Synthesis | Chemical Reviews
Iron Catalysis in Organic Synthesis: A Critical Assessment of What It Takes To Make This Base Metal a Multitasking Champion

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.1273-86-5,Ferrocenemethanol,as a common compound, the synthetic route is as follows.

General procedure: A mixture of aryl alcohol (1 mmol) and [FemDMMerA]Y (100 mg) in solvent(5 mL) was refluxed in oil bath. After completion of the reaction as monitored byTLC, the reaction mixture was filtered to remove insoluble SILP catalyst.Evaporation of solvent in vacuuo followed by column chromatography over silicagel using petroleum ether/ethyl acetate (95:5 v/v) afforded pure aldehydes.

1273-86-5, The synthetic route of 1273-86-5 has been constantly updated, and we look forward to future research findings.

Reference£º
Article; Kurane, Rajanikant; Bansode, Prakash; Khanapure, Sharanabasappa; Salunkhe, Rajashri; Rashinkar, Gajanan; Research on Chemical Intermediates; vol. 42; 12; (2016); p. 7807 – 7821;,
Iron Catalysis in Organic Synthesis | Chemical Reviews
Iron Catalysis in Organic Synthesis: A Critical Assessment of What It Takes To Make This Base Metal a Multitasking Champion

Ferrocenecarboxylic acid, cas is 1271-42-7, it is a common heterocyclic compound, the iron-catalyst compound, its synthesis route is as follows.,1271-42-7

In a three-necked flask, 4.6 g (0.02 mmol) of dry ferrocenecarboxylic acid and 80 mL of anhydrous benzene were added.Under nitrogen protection,6.24 g (0.03 mmol) of phosphorus pentachloride was slowly added in several portions, and stirred at room temperature for 3 h.The benzene is distilled off under reduced pressure, and petroleum ether (60-90 C) is extracted to obtain a deep red solution, distilled under reduced pressure, and cooled.Dark red needle crystals are precipitated, yield 80%

As the rapid development of chemical substances, we look forward to future research findings about 1271-42-7

Reference£º
Patent; Guilin Medical University; Huang Wanyun; Liao Ying; Peng Xiangyan; Yin Penglong; Liao Yueying; (13 pag.)CN104788503; (2017); B;,
Iron Catalysis in Organic Synthesis | Chemical Reviews
Iron Catalysis in Organic Synthesis: A Critical Assessment of What It Takes To Make This Base Metal a Multitasking Champion

14024-18-1, Iron(III) acetylacetonate is a iron-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

Synthesis of ferrimagnetic nanocubes ( Fe3O4 ) was carried out under nitrogen (N 2).Typical synthesis of mangnetic nanocubes ( 0.71g,2 mmol ) Iron ( III ) acetylacetonate (Fe(acac)3) mixed with ( 0.41 g,2.1 mmol ) 4-biphenylacarboxylic acid added to mixture ( 1.129 g , 4 mmol ) oleic acid and ( 10.40 g ,10 ml ) benzyl ether . The mixture solution was degassed at room temperature for 1 hour .The solution was then heated to 290C at the rate of 20C /min with vigorous magnetic stirring at 290 rpm to get ferrimagnetic nanocubes. where the temperature was held for 30 min when temperature reached 290C . After cooling the solution to room temperature , a mixture of ( 40 ml ) toluene and ( 10 ml ) hexane was added to solution . The solution was then centrifuged at 5000 rpm for minutes to precipitate the magnetite nanocubes .The precipitate was washed using ( 10 ml ) chloroform ( CHCl3 ) . Then after that used oven vacuum to obtain Fe3O4 nanocubes in powder form at 80C temperature14- 18., 14024-18-1

As the paragraph descriping shows that 14024-18-1 is playing an increasingly important role.

Reference£º
Article; Alkadasi, Nabil Abdullah Noman; Oriental Journal of Chemistry; vol. 30; 3; (2014); p. 1179 – 1182;,
Iron Catalysis in Organic Synthesis | Chemical Reviews
Iron Catalysis in Organic Synthesis: A Critical Assessment of What It Takes To Make This Base Metal a Multitasking Champion

A common heterocyclic compound, the iron-catalyst compound, name is Vinylferrocene,cas is 1271-51-8, mainly used in chemical industry, its synthesis route is as follows.,1271-51-8

General procedure: As shown as the synthetic protocol A in Scheme 2, compounds 1-11 were synthesized following literature description [16] with m-methoxyphenol, p-methoxyphenol, resorcinol, and hydroquinone as reagents. One hydroxyl group in resorcinol and hydroquinone was protected by tert-butyldimethylsilyl chloride. Then, 17 mL of dry CHCl3 solution containing excess PhtNSCl was added dropwisely to 8 mL of dry CHCl3 solution containing monoprotected hydroquinone or resorcinol and stirred for 16 h at 0 ¡ãC until phenols cannot be detected by thin layer chromatography (TLC). The mixture was diluted with CH2Cl2 and washed by saturated NaHCO3 and water. The organic phase was dried over anhydrous Na2SO4, and the solvent was removed under vacuum. The residue was purified by column chromatography with CH2Cl2 as the eluent to afford thiophthalimides as colorless solid. The following cycloaddition reactions were carried out in dry CHCl3 solution of thiophthalimides (~ 0.1 M) and styrenes (2 equiv.) or vinyl ferrocene (2 equiv.) and freshly distilled (C2H5)3N (2 equiv.) at 60 ¡ãC. The reaction was finished with thiophthalimides not detected by TLC. Then, the solvent was evaporated under vacuum pressure, and the residual solid was purified with column chromatography to afford silylated adducts. The desilylation operation was performed in dry tetrahydrofuran (THF) solution containing 0.04 M aforementioned adducts at 0 ¡ãC, to which a solution of (n-C4H9)4NF*3H2O in THF (1 equiv. for each protective group) was added. The reaction was finished with the reagent not detected by TLC, and then the mixture was diluted with ethyl acetate and washed with saturated NH4Cl and water. The organic layer was dried over anhydrous Na2SO4, and the solvent was evaporated under vacuum pressure. The residue was purified with column chromatography to afford thiaflavans.

As the rapid development of chemical substances, we look forward to future research findings about 1271-51-8

Reference£º
Article; Lai, Hai-Wang; Liu, Zai-Qun; European Journal of Medicinal Chemistry; vol. 81; (2014); p. 227 – 236;,
Iron Catalysis in Organic Synthesis | Chemical Reviews
Iron Catalysis in Organic Synthesis: A Critical Assessment of What It Takes To Make This Base Metal a Multitasking Champion

A common heterocyclic compound, the iron-catalyst compound, name is Iron(III) acetylacetonate,cas is 14024-18-1, mainly used in chemical industry, its synthesis route is as follows.,14024-18-1

General procedure: Monodisperse synthetic Fe1-xMgxFe2O4 (x=0, 0.1, 0.2, 0.3, 0.4, & 0.5) nanospheres were synthesized by recently developed solvothermal reflux method using high boiling point organic solvents mixture as reaction solvent [14,15]. Iron(III) acetylacetonate or Fe(C5H7O2)3 (solid, 97 %, Sigma-Aldrich), Magnesium acetylacetonate or Mg(C5H7O2)2 (solid, 97 %, Aldrich) were used as metal precursors. Benzyl ether (liquid, 98 %, Aldrich, boiling point (bp): 298C) and oleylamine (liquid, 70 %, Aldrich, bp: 364C) solvents mixture as reaction solvent, and oleic acid (liquid, 65 %, SDFCL, bp: 360C) as surfactant were used. To synthesize 0.5g of target composition compound, 40mL of benzylether (BE) and 10mL of oleylamine (OAm) solvents mixture were taken as reaction solvent in three neck round bottom (RB) flask (250mL). The mixture was stirred with magnetic stirrer for 10min. to make it homogeneous. Metal precursor powders were finely grounded to enhance their decomposition. Stoichiometric metal precursor fine powders were added to the reaction solvents mixture. The mixture was stirred for 10min. to make homogeneous solution. Then 5mL of oleic acid (OA) (?2.5 times of metal cations mols) was added. The resultant reactants mixture was heated to boiling point of the solvent mixture (300C) by electric heating mantle at 5C/min ramp. The boiling solvents produce natural gas bubbles. The reaction was carried out for 1h at this temperature and then naturally cooled the RB flask to room temperature. To precipitate crystallined ferrite nanoparticles, anti-solvent such as ethanol was added to the reaction mixture. The precipitated nanoparticles were separated by sedimentation principle through centrifugation. The nanoparticles were redispersed in good solvents such as n-hexane. To further purify the nanoparticles from residual organic molecules (surfactant), the redispersed particles were precipitated, separated and redispersed by the above procedure, at least two times.

As the rapid development of chemical substances, we look forward to future research findings about 14024-18-1

Reference£º
Article; Manohar; Krishnamoorthi; Journal of Magnetism and Magnetic Materials; vol. 443; (2017); p. 267 – 274;,
Iron Catalysis in Organic Synthesis | Chemical Reviews
Iron Catalysis in Organic Synthesis: A Critical Assessment of What It Takes To Make This Base Metal a Multitasking Champion

1273-86-5, Ferrocenemethanol is a iron-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

A mixture of K2CO3 (1 mmol) and the catalyst (52 mg, ?3 mol% of Pd2+) in toluene (5 ml) was prepared in a two necked flask. The flask was evacuated and refilled with pure oxygen. To this solution, the alcohol (1 mmol, in 1 ml toluene) was injected and the resulting mixture was stirred at 80 C under an oxygen atmosphere. After completion of reaction, the reaction mixture was filtered off and the catalyst rinsed twice with CH2Cl2 (5 ml). The excess of solvent was removed under reduced pressure to give the corresponding carbonyl compounds.

1273-86-5, As the paragraph descriping shows that 1273-86-5 is playing an increasingly important role.

Reference£º
Article; Alizadeh; Khodaei; Kordestania; Beygzadeh; Journal of Molecular Catalysis A: Chemical; vol. 372; (2013); p. 167 – 174;,
Iron Catalysis in Organic Synthesis | Chemical Reviews
Iron Catalysis in Organic Synthesis: A Critical Assessment of What It Takes To Make This Base Metal a Multitasking Champion

A common heterocyclic compound, the iron-catalyst compound, name is Vinylferrocene,cas is 1271-51-8, mainly used in chemical industry, its synthesis route is as follows.,1271-51-8

Vinylferrocene (1.50 g, 7.07 mmol), 4-iodobenzaldehyde(0.684 g, 2.95 mmol), palladium(II) acetate (0.0331 g,0.147 mmol) and tri-o-tolyl-phosphine (0.224 g, 0.767 mmol) weredissolved in a 1:10 solution (v/v) of triethylamine and acetonitrile (30 ml). The dark red reaction mixturewas stirred under N2 at 82 Cfor 24 h. After cooling, the solvent was removed and resulting redresidue was dissolved in 25 ml DCM and 25 ml water added. Theorganic layer was separated and the aqueous layer washed withDCM (3 25 ml). The organic fractions were combined, stirred overanhydrous MgSO4 and removed by gravity filtration. The filtratewas collected and the solvent removed to give a dark red residue.The product was purified by column chromatography, initially usinga solvent system of 100percent petroleum ether, followed by 50:50mixture of petroleum ether (40-60 C) and DCM. The desiredproduct (1) was isolated as a dark red powder (0.680 g, 73percent). Mp:decomposition without melting, onset at 110 C. 1H NMR(399.951 MHz, CDCl3): d (ppm) 9.97 (s, 1H, CHO), 7.83 (d, 2H,J 8.3 Hz, ArH), 7.56 (d, 2H, J 8.4 Hz, ArH), 7.07 (d, 1H, J 16.1 Hz,HC]CH), 6.73 (d, 1H, J 16.1 Hz, HC]CH), 4.51 (t, 2H, Cp), 4.35 (t,2H, Cp), 4.16 (s, 5H, Cp). 13C{1H} NMR (100.635 MHz, CDCl3):d (ppm) 191.55, 144.07, 134.67, 131.52, 130.32, 126.07, 124.60,82.25, 69.76, 69.38, 67.37. IR (KBr, cm1) n 1693 (C]O), 1630 (C]C). EI-MS: m/z 316 ([M], 100percent). Elemental Analysis forC19H16FeO0.5H2O calculated C, 70.18; H, 5.27, found C, 70.39; H,5.07percent.

As the rapid development of chemical substances, we look forward to future research findings about 1271-51-8

Reference£º
Article; Baartzes, Nadia; Stringer, Tameryn; Seldon, Ronnett; Warner, Digby F.; De Kock, Carmen; Smith, Peter J.; Smith, Gregory S.; Journal of Organometallic Chemistry; vol. 809; (2016); p. 79 – 85;,
Iron Catalysis in Organic Synthesis | Chemical Reviews
Iron Catalysis in Organic Synthesis: A Critical Assessment of What It Takes To Make This Base Metal a Multitasking Champion

1271-42-7, Ferrocenecarboxylic acid is a iron-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

Chlorocarbonyl ferrocene 2b: The synthesis of chlorocarbonyl ferrocene 2b was adapted from a procedure of Cormode et al. {Dalton Trans. 2010, 39, 6532). After suspending ferrocenecarboxylic acid 2a (462 mg, 2.01 mmol) in dry CH2CI2 (23 mL), oxalyl chloride (1 100 mu, 13.64 mmol) in dry CH2CI2 (10 mL) was added dropwise to the reaction mixture whereby the orange suspension turned dark red. The reaction mixture was refluxed for 2 h and then stirred overnight at room temperature. The solvent was then removed under vacuum. The product 2 was not purified and used immediately for the next synthetic step.

1271-42-7, As the paragraph descriping shows that 1271-42-7 is playing an increasingly important role.

Reference£º
Patent; UNIVERSITAeT ZUeRICH; THE UNIVERSITY OF MELBOURNE; GASSER, Gilles; GASSER, Robin B.; HESS, Jeannine; JABBAR, Abdul; PATRA, Malay; WO2015/44395; (2015); A1;,
Iron Catalysis in Organic Synthesis | Chemical Reviews
Iron Catalysis in Organic Synthesis: A Critical Assessment of What It Takes To Make This Base Metal a Multitasking Champion

1271-55-2, Acetylferrocene is a iron-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

General procedure: To a stirred suspension of p-toluenesulfonyl hydrazide (1eq.) in water (12mL) and three drops of HCl 32%, the formyl or acetyl organometallic precursor (1eq.) was added. The resulting mixture was stirred for 18h at room temperature. The precipitate obtained was washed with water (2¡Á10mL) and dried under vacuum. The hydrazone derivatives were recrystallized from acetone/hexane (1:5) at -18C

1271-55-2, The synthetic route of 1271-55-2 has been constantly updated, and we look forward to future research findings.

Reference£º
Article; Concha, Camila; Quintana, Cristobal; Klahn, A. Hugo; Artigas, Vania; Fuentealba, Mauricio; Biot, Christophe; Halloum, Iman; Kremer, Laurent; Lopez, Rodrigo; Romanos, Javier; Huentupil, Yosselin; Arancibia, Rodrigo; Polyhedron; vol. 131; (2017); p. 40 – 45;,
Iron Catalysis in Organic Synthesis | Chemical Reviews
Iron Catalysis in Organic Synthesis: A Critical Assessment of What It Takes To Make This Base Metal a Multitasking Champion